Construction & Repair Housekeeping Home Appliances Gardening Interior Design Furniture & Woodworking Plumbing & Electric Landscaping Eco-Friendly Flower Arrangement Home & Garden WonderHowTo

Active Tools & Equipment Posts

iOS 17 Tips, Tricks, How-Tos, News

How To: Avoid stripping gears on a Rain Bird sprinkler head

Avoid stripping the gears in your Rain Bird 5000 Series Rotor Sprinkler Heads by never turning the turret against the turn. Sean Stefan from Sprinkler Daddy explains in this video tutorial that if you start turning from the left fixed edge to the right, never go back to the left until you've gone all the way to the right. If you don't follow these guidelines, you run the risk of stripping the gears in your Rain Bird 5000 Series sprinkler heads. Then what are you going to water your lawn with....

How To: Copy a key with a Coke can

This is a how-to video explaining how to copy a key with a can of cola. All you need is an aluminum soda or beer can. To make it come out better, add a additional side to the one piece. This technique works well when you don't have time to get a new key cut. Watch this video tutorial and learn how to duplicate a key with a Coke can.

How To: Operate and maintain a chainsaw

This two-part chainsaw safety maintenance and operation instuctional video was developed to give chainsaw operators the basic information needed to properly and safely use a chainsaw. Although this program covers a wide variety of subjects, you should always read and fully understand your own chainsaw's operation manual. For more information on using and maintaing chainsaws, take a look.

How To: Restore and Sharpen Rusted Scissors

Leaving scissors wet or forgetting them outside can cause them to rust. Rusty scissors, if you can even open them, will leave brown marks on everything you attempt to cut through. Attempt is the truth—rust dulls the blades of the scissors making it virtually impossible to cut through any type of material, ranging from paper to fabric. But don't toss the scissors in the trash just yet. You can restore rusted scissors to a usable condition provided they are not completely covered and have rust ...

How To: Read a Tape Measure

If you don't work in construction or are a woodworking master, you probably aren't entirely sure what all those marks are on a tape measure. Sure, you likely know the basics, like there are 12 inches to a foot, but what are all those little tick marks for? Don't let all those little lines dissuade you from using a tape measure. Follow these guidelines to help you read all those little ruler marks.

How To: Clean a 2 cycle engine carburetor from a Ryobi trimmer

If you own a Ryobi trimmer and wish to perform some regular maintenance work on it, you may want to check out this next video. In the tutorial, you find out how to clean a 2 cycle engine carburetor from the Ryobi trimmer using some simple pieces. It's not too difficult to do and can be really handy when you want to make sure your machine is working at optimal capability. So check out the video above, pay attention, be careful, and enjoy!

How To: Fix an oil leak on a KitchenAid stand mixer

In this DIY guide from the folks at the eReplacementParts], we learn how to repair an oil leak on a KitchenAid stand mixer. It's easy! So easy, in fact, that this clip can present a complete overview of the technique in about two minutes. For all of the details, and to learn how to repair a leaky KitchenAid mixer, take a look.

How To: Make a cutting disc for a Dremel rotary tool

Get a little use out of those empty tin cans you are going to throw away. Recycle them into a cutting disc. So, check out this video tutorial to see how to make a cutting disc for a Dremel rotary tool. These Dremel cutting disks are pretty easy to make. Just get a can opener, take off the lid of one of your junk aluminum cans, and begin to disc away. You'll need a Dremel sanding disc for a stencil reference. These are less dangerous than normal sharp cutting disks, not to mention cheap.

How To: Pop a Car Lock with a Coat Hanger

You've done it, I've done it, almost everyone who owns a car has done it: they've gone an locked themselves out. Well, this good how-to shows how to get back into your older model car with nothing more than a coat hanger. It will requre some trial and error to get it done, but this video is a good primer.

How To: Use an angle grinder safely in home construction projects

Angle grinders are very powerful and useful tools, but like many such power tools they are extremely dangerous if you don't know how to use them. This video goes over a variety of must-know safety precautions that you should take before using an angle grinder to grind for your own construction projects. It covers proper eyewear, fire protection, and setting up the device for use.

How To: Open a bedroom or bathroom door when you're locked out

Ahhh! You're locked out of your bedroom, or your bathroom! Well, watch this video and you won't be locked out for long. Fortunately, interior privacy locks are very simple to pick. There are essentially two kinds: one that requires a blade, or knife and the other which requires a long sharp "pin" like object to insert into the handle. Check out this video and never be locked out again! You'll need something like a flat head screw driver for locks with a "slot" in them, and something long and ...

How To: Easily weather seal your garage door

If you have a garage door attached to your home, it's important to know that it's a space that needs proper insulation as well. Not doing so can lead to a room that is cold to walk into and can cause other rooms in your home to become cold as well. In this next tutorial, you'll find out what you need to do in order to easily weather seal your garage door. Enjoy!

How To: Install a drip irrigation watering system

Check out this landscaping video tutorial to see how to install a drip irrigation watering system. You'll need this if you want to keep your garden looking great. You will have to poke a hole in the pipe for every shrub. Then, you'll need to install a coupler. This drip irrigation installation is explained in simple English by Sprinkler Daddy's Sean Stefan.

How To: Open a locked bedroom or bathroom door

Getting locked out of a bedroom or bathroom can be a real bummer. Fortunately, these locks are easy to "pick" and get yourself in. This how to shows you clearly what to do to get yourself back inside so you don't feel frustrated all day long. This excellent video takes you step by step through the process. This video talks about 2 different types of locks and the two different types of tools you'll need.

How To: Decode a combination lock

In this video tutorial, viewers learn how to decode a combination lock. Users will need a feeler gauge strip with a modified tip. Begin by sliding the feeler gauge strip in between the wheel and body of the lock. Then start rotating the wheel. When the wheel has resistance, notch the wheel in the right place. Then rotate the wheel counter clockwise three clicks. Do the same for the rest of the numbers on the lock. This video will benefit those viewers who have a combination lock, and would li...

How To: Use an engraving tool

In this tutorial, we learn how to use an engraving tool. It doesn't matter how old your engraving tool is, just make sure it has different speeds on it to help control it while in use. Now, place a piece of aluminum down and adjust your power level to the lowest level. Push down on the aluminum and write the word you want to so you can see how the pressure effects the aluminum. Now, set the tool at the highest setting and push down on a sledge hammer to see the pressure you need to push to ge...

How To: Replace the line on a STIHL trimmer Head

In this video, we learn how to replace the line on a STIHL trimmer head. First, remove the spool from the head by stopping the engine and cutting attachment first. Then, grasp the body and insert your thumb into the tab on the head, then rotate around and press on the second tab. After this, press down on the spool and release it from the housing. Now, remove the star nut to remove the head completely. Now, you can replace it with a new one. After this, replace the parts that you took out and...

How To: Pick a lock easily with 2 paper clips

ZurplusFaction shows viewers how to pick a lock easily using 2 paper clips. First, you need to take your first paper clip and fold one end out. Fold it out again and straighten this out. Next, take the folded out in and fold in again so it forms boomerang shape with the paper clip. Now, take your pliers and squeeze this folded part together tightly. With a bigger paperclip, and use wire cutters to cut of a straight piece of the paper clip with a curve at the top. Now, you are ready to pick yo...

How To: Create an electric tool belt

Tim Carter demonstrates the basic tools (pliers, screwdrivers, strippers) you need for residential electrical repairs, as well as a handy little tool-belt pouch that stores all of the tools. Video shows not only how to create your own electricians tool belt but also how to use each individual tool.

How To: Start a Briggs and Stratton Power Generator After 3 Years

My Briggs and Stratton power generator wasn't used for 3 years. Trying to start it again, lead to some problems. The video will show you the true story and the solution. The first problem was, that it lost some fuel - the fuel pipe was broken. In good hope I tried again to start it, but it stopped within seconds. A check of the spark plug to find a very dirty one. After cleaning the spark plug, the engine ran, but only for a few seconds. It lost a lot of fuel and stopped again. The fuel was c...

How To: Magnetize a Screwdriver

Oftentimes, when using a screwdriver it can be hard to keep the screw connected to the screwdriver. In this article, we show a trick on how you can magnetize your screwdriver so the screw will hold onto your screwdriver. Get a heavy duty magnet.

How To: Inject Your Drill Press Table Crank with Steroids

First, I would like to explain that among my family members, I am considered somewhat of an oddball. Mostly because of some of the mods that I have performed on a few of my woodworking tools. After I show you what I did to my drill press, you may be inclined to agree. When I first hatch an idea in my little pea brain, the first thing I take into consideration is whether or not this mod is irreversible and will destroy my tool. In the case of my drill press, I determined that it was safe to pr...

Prev Page